集扣 專業從事高品質、高精度螺栓
| 公稱直徑 ① | 0.6 | 0.8 | 1 | 1.2 | 1.6 | 2 | 2.5 | 3.2 | ||
| d | 最大值 | 0.5 | 0.7 | 0.9 | 1 | 1.4 | 1.8 | 2.3 | 2.9 | |
| 最小值 | 0.4 | 0.6 | 0.8 | 0.9 | 1.3 | 1.7 | 2.1 | 2.7 | ||
| α | 最大值 | 1.6 | 1.6 | 1.6 | 2.5 | 2.5 | 2.5 | 2.5 | 3.2 | |
| 最小值 | 0.8 | 0.8 | 0.8 | 1.25 | 1.25 | 1.25 | 1.25 | 1.6 | ||
| b | ≈ | 2 | 2.4 | 3 | 3 | 3.2 | 4 | 5 | 6.4 | |
| c | 最大值 | 1 | 1.4 | 1.8 | 2 | 2.8 | 3.6 | 4.6 | 5.8 | |
| 最小值 | 0.9 | 1.2 | 1.6 | 1.7 | 2.4 | 3.2 | 4 | 5.1 | ||
| 適用螺栓直徑 | ≤ 2.5 | ＞2.5, ≤ 3.5 | ＞3.5, ≤ 4.5 | ＞4.5, ≤ 5.5 | ＞5.5, ≤ 7 | ＞7, ≤ 9 | ＞9, ≤ 11 | ＞11, ≤ 14 | ||
| 適用U形銷直徑 | ≤ 2 | ＞2, ≤ 3 | ＞3, ≤ 4 | ＞4, ≤ 5 | ＞5, ≤ 6 | ＞6, ≤ 8 | ＞8, ≤ 9 | ＞9, ≤ 12 | ||
| 千件鋼制重≈kg | - | - | - | - | - | - | - | - | ||
| 公稱直徑 ① | 4 | 5 | 6.3 | 8 | 10 | 13 | 16 | 20 | ||
| d | 最大值 | 3.7 | 4.6 | 5.9 | 7.5 | 9.5 | 12.4 | 15.4 | 19.3 | |
| 最小值 | 3.5 | 4.4 | 5.7 | 7.3 | 9.3 | 12.1 | 15.1 | 19 | ||
| α | 最大值 | 4 | 4 | 4 | 4 | 6.3 | 6.3 | 6.3 | 6.3 | |
| 最小值 | 2 | 2 | 2 | 2 | 3.15 | 3.15 | 3.15 | 3.15 | ||
| b | ≈ | 8 | 10 | 12.6 | 16 | 20 | 26 | 32 | 40 | |
| c | 最大值 | 7.4 | 9.2 | 11.8 | 15 | 19 | 24.8 | 30.8 | 38.5 | |
| 最小值 | 6.5 | 8 | 10.3 | 13.1 | 16.6 | 21.7 | 27 | 33.8 | ||
| 適用螺栓直徑 | ＞14, ≤ 20 | ＞20, ≤ 27 | ＞27, ≤ 39 | ＞39, ≤ 56 | ＞56, ≤ 80 | ＞80, ≤ 120 | ＞120, ≤ 170 | ＞170 | ||
| 適用U形銷直徑 | ＞12, ≤ 17 | ＞17, ≤ 23 | ＞23, ≤ 29 | ＞29, ≤ 44 | ＞44, ≤ 69 | ＞69, ≤ 110 | ＞110, ≤ 160 | ＞160 | ||
| 千件鋼制重≈kg | - | - | - | - | - | - | - | - | ||
| ①,公稱直徑等于開口銷孔的直徑。對銷孔直徑推薦的公差為： 公稱直徑≤1.2: H13; 公稱直徑>1.2: H14 根據供需雙方協議，允許采用公稱規格為3、6和12mm的開口銷 。 | ||||||||||
Copyright ? 2023 魯ICP備2023025064號-1 技術支持：海誠互聯 站點地圖
